Servo Siemens V90 MOTOR
SIMOTICS S-1FL6 servomotors are naturally cooled, permanent-magnet synchronous motors where the heat is dissipated through the motor surface. The motors can be simply and quickly installed using the full thread and quick-release connectors. They have a 300 percent overload capability and can be combined with SINAMICS V90 converter to create a powerful servo system with a high degree of functionally.
SIMOTICS S-1FL6 servomotor – SINAMICS V90 system
SIMOTICS S-1FL6, Low Inertia (LI) for high dynamic Performance
SIMOTICS S-1FL6, LI, Shaft heights 20, 30, 40, 50 mm
Technical data |
|
|---|---|
Shaft heights: |
20 mm, 30 mm, 40 mm, 50 mm |
Rated torque: |
0.16 Nm up to 6.37 Nm |
Rated/max. speed: |
3000 rpm / 5000 rpm |
Encoder: |
Incremental encoder TTL 2500 ppr; |
Degree of protection: |
IP65 |
Option: |
Holding brake |
Shaft type: |
Plain shaft or feather key |
SIMOTICS S-1FL6, High Inertia (HI) for smooth operation performance
SIMOTICS S-1FL6, HI, Shaft heights 95, 65, 45 mm
Technical data |
|
|---|---|
Shaft heights: |
45 mm, 65 mm, 95 mm |
Rated torque: |
1.27 Nm up to 33.40 Nm |
Rated/max. speed: |
2000 rpm / 3000 rpm |
Encoder: |
Incremental encoder TTL 2500 ppr; |
Degree of protection: |
IP65 |
Option: |
Holding brake |
Shaft type: |
Plain shaft or feather key |
Servo SIEMENS V90 CABLE
Select your MOTION-CONNECT 300 connection system
• Power cable acc. to length and cross section (orange)
• Encoder cable acc. to length and encoder type (green)
• Brake cable if motor holding brake is selected acc. to length (black)
• Control/setpoint cable to connect the drive to the PLC (grey)
• Connectors can also be ordered separately
Cables and connectors – SINAMICS V90 system
|
Power cable |
Encoder cable |
Brake cable |
Setpoint cable |
|---|---|---|---|---|
|
|
|
|
|
Length |
3 m |
3 m |
5 m |
Control/setpoint cable, 1 m cable, with a connector (MDR 50-pin connector, free pins to controller side) |
Length |
5 m |
5 m |
5 m |
|
Length |
7 m* |
7 m* |
7 m* |
|
Length |
10 m |
10 m |
10 m |
|
Length |
20 m |
20 m |
20 m |
|
Option |
|
For incremental Encoder |
|
|
Option |
|
For absolute Encoder |
|
|
* 7 m cable length is only available for high inertia motors (3 AC 400V) |
||||
PROFINET Cable |
|
|
|---|---|---|
|
|
|
IE FC RJ45 Plug with IE FC TP Trailing Cable |
IE FC TP Standard Cable 2x2 |
IE CONNECTING CABLE IE FC RJ45 PLUG-180 |
Connectors |
|
|
|
|
|
|---|---|---|---|---|---|
|
|
|
|
|
|
Encoder connector |
50-pin MDR connector for setpoint cable |
Power connector |
Brake connector |
Incremental 13-bit encoder connector |
Absolute 20-bit encoder connector (only for high intertia 3AC 400V) |
Converter side |
Converter side |
Motor side |
Motor side |
Motor side |
Motor side |
