JWTECH.co.,LTD LOGO








  Panasonic Sensors > Fiber Sensors|| Area Sensors | Light Curtains / Safe Components | Pressure Sensors | Flow Sensors | Proximity Sensors | Particular Use Sensors | Machine Vision System | Photoelectric Sensors | Micro Photoelectric Sensors
 
Integrated Display Type Digital Flow Sensor FM-200
Integrated Display Type Digital Flow Sensor FM-200
CE※1
※1 Conforming to EMC Directive


Easy-to-see dual color with sub display!

The setting conditions are displayed on the sub display, making it much easier to keep track of operations.
In addition, the digital display which switches between 2 colors lets you check the status of sensor operation at a glance.

Easy-to-see dual color with sub display!

High precision of ±3 % F.S.

A new rectification mechanism and Micro Electro Mechanical System (MEMS) technology allow the sensor to be mounted on a Si sensor chip (3 x 3.5 mm0.118 x 0.138 in). This provides an extremely small heat capacity, high precision of ±3 % F.S. and high-speed response. The two temperature sensors on each side of the heater detect the heat distribution to make bidirectional detection possible.

One sensor for both intake and exhaust

A single sensor can detect flows bidirectionally. In addition, it can be set to detect flows in either the forward or reverse direction only, making it suitable for a variety of applications.

One sensor for both intake and exhaust

No straight pipes needed

The rectification method used by the new mechanism makes straight pipes unnecessary at both the intake and exhaust sides.

No straight pipes needed

Connection

Quick connection is possible with a cover-attached connector.

Connection

Flexible installation direction

Other than the ability to carry out bidirectional detection, there are no limitations on the installation direction, making the installation very flexible.

Flexible installation direction

Equipped with a wide variety of functions for greater ease of use

  • Integrated value reset function
    During integrated mode, external input allows reset of the integrated value.
  • Analog voltage output
    1 to 5 V analog voltage output is incorporated.
  • Key lock function
    Key operation can be disabled to prevent mis-operation.
  • Rattle prevention function (Response time setting)
    The response time can be set to one of seven steps from 50 ms to approximately 1,500 ms. This prevents rattling from rapid changes in flow or from noise.
  • Display rate setting
    The display update period for the digital display can be changed to 250 ms, 500 ms or 1,000 ms in order to eliminate display flickering.
  • ECO mode
    After approx. one minute of no operation, sensor will be switched to ECO mode.
    Backlight will be turned off to reduce power consumption.

Suitable for cost and quality control! Integrated output mode incorporated

The FM-200 series can control and manage flows in a wide variety of output modes such as integrated output mode, depending on the required application.

Integrated output mode
■ Quality control

When the volume of flow of the gas being measured reaches the set integrated value, output switches to ON or OFF.
・Controls N2 charging volumes for electronic components
・Controls air blowing volumes, etc.

Quality control

Integrated pulse output mode
■ Cost management

The pulse output is generated once at every specified integrated value*. This lets you know the amount of air consumed per unit of time easily.

* Integrated values are specified by range and can vary. For details, refer to "SPECIFICATIONS".

・Controls N2 purge volumes in reflow furnaces
・Controls overall volumes of air consumed by equipment, etc.

Cost management

■ Energy-saving and environmental-friendly
The pulse output from the flow sensor can be inputted to the pulse counter of an Eco-Power Meter so that air consumption and power consumption can both be measured simultaneously.

Energy-saving and environmental-friendly
Notes:
1) Displayed value data is not outputted.
2) For details, refer to "KW8M Eco-Power Meter".

INSTANT FLOW RATE DISPLAY (FACTORY SETTING)

  • Window comparator mode
    This mode is used for setting comparative output to ON or OFF at flow rates within the setting range.
Window comparator mode
  • Hysteresis mode
    This mode is used for setting comparative output hysteresis to the desired level and for carrying out ON / OFF control.
Hysteresis mode
  • Output OFF mode
    Comparative output is forcibly maintained at OFF regardless of the setting value.
Output OFF mode
Type Appearance Applicable
fluid
Flow rate
range
Model No. Port size Comparative output
Resin
body
type
Clean air (Note)
Compressed air (Note)
Nitrogen gas
500mℓ/min. FM-252-4 ø4 ø0.157push-in NPN Open-collector transistor
FM-252-4-P PNP Open-collector transistor
1,000mℓ/min. FM-213-4 NPN Open-collector transistor
FM-213-4-P PNP Open-collector transistor
5ℓ/min. FM-253-4 NPN Open-collector transistor
FM-253-4-P PNP Open-collector transistor
10ℓ/min. FM-214-4 NPN Open-collector transistor
FM-214-4-P PNP Open-collector transistor
50ℓ/min. FM-254-8 ø8 ø0.315push-in NPN Open-collector transistor
FM-254-8-P PNP Open-collector transistor
100ℓ/min. FM-215-8 NPN Open-collector transistor
FM-215-8-P PNP Open-collector transistor
Aluminum
body
type
500ℓ/min. FM-255-AR2 Rc1/2female thread NPN Open-collector transistor
FM-255-AR2-P PNP Open-collector transistor
FM-255-AG2-P G1/2female thread PNP Open-collector transistor
1,000ℓ/min. FM-216-AR2 Rc1/2female thread NPN Open-collector transistor
FM-216-AR2-P PNP Open-collector transistor
FM-216-AG2-P G1/2female thread PNP Open-collector transistor
Note : The clean air complies with JIS B 8392-1.1.1 to 5.6.2, and the compressed air complies with JIS B 8392-1.1.1 to 1.6.2.

Accessory

CN-F15-C1 (Connector attached cable 1 m 3.281 ft)

CN-F15-C1


 

 

LiveZilla Live Chat Software
   JWTECH.CO.LTD., Tel: (662) 733 7702 (Auto), Fax: (662) 733 7703 COPYRIGHT 2011
JWTECH.CO.LTD., ALL RIGHTS RESERVED.   

PLC | Servo | Inverter | HMI | Instruments | Blog